Skip to content
TRUEBUILTREMODELING

Farm and ranch water

Pond and concrete cattle waterer repair

TrueBuilt repairs pond-fed livestock watering systems across southeast Kansas and northeast Oklahoma: the concrete waterer, the float valve, the valves and buried line, and the intake out in the pond.

If the tank is dry, overflowing, freezing, or the ground is wet along the line, we trace the system from the pond to the waterer, find what failed, and give you written pricing before the repair.

How a pond-fed waterer system works

Most pond waterers in this area are gravity systems. A screened intake sits out in the pond, often held below the surface by a float. A buried line runs downhill from the pond, past the dam, to a mostly buried concrete waterer below it. Valves let the line be shut off, a float valve keeps the tank full, and a drain carries overflow away from the pad.

When any one part fails, the cattle notice first. Finding the actual failure point matters more than replacing parts at random.

Common problems we fix

No water or a slow trickle at the tank. Usually a plugged intake screen, a stuck float valve, sediment in the line, a closed or failed valve, air trapped in the pipe, or a pond level that has dropped below the intake.

Tank overflowing or running all the time. A worn float valve or seat that will not shut off. Left alone it wastes pond water and turns the area around the waterer into mud.

Waterer freezing in winter. Lost soil cover over the buried tank, an exposed or shallow line, a drain that is not doing its job, or a waterer that was set too high and open to the wind.

Wet ground, sinkholes, or seepage along the line. A broken or separated pipe joint, or water running along the outside of the pipe. Near the dam this needs attention before it becomes an erosion problem.

Cracked or shifted concrete tank. Settling, frost heave, or livestock pressure on the soil cover can crack the tank or pull the connection loose.

Siphon line that keeps losing prime. Air collects at the high point over the dam and flow stops without warning. We check the line and valves and talk through whether the setup can be made more dependable.

How the repair visit works

1. Walk the system. We start at the pond intake and follow the line to the waterer, checking the intake, valves, wet spots, the tank, the float, and the drain.

2. Find the failure. We isolate whether the problem is supply, the line, or the waterer itself before recommending a repair.

3. Written pricing. You get the repair, the parts, and the price in writing before work starts.

4. Repair and test. After the repair, the line is flushed, the float and valves are tested, and the flow at the tank is checked before we leave.

What to send before the visit

Send the property town, photos of the waterer, the pond, and any wet or sunken spots along the line, what the waterer is doing now, about how many head drink from it, and how long it has been happening. If cattle are without water, say so when you call.

Waterer down?

Call or send the property town and a few photos. TrueBuilt is based in Oswego, KS.

Call (918) 238-9816

Frequently asked questions

Do you repair pond-fed concrete cattle waterers?

Yes. TrueBuilt repairs existing pond-to-waterer systems in southeast Kansas and northeast Oklahoma, including the concrete waterer, float valve, drain, valves, buried pipeline, and the pond intake.

Why is my pond waterer not getting water?

The common causes are a clogged intake screen, a stuck or worn float valve, sediment or air in the line, a failed valve, a broken pipe, or a pond level that has dropped below the intake. We trace the system from the pond to the tank to find which one it is.

Why does my concrete waterer freeze?

These waterers rely on soil cover and buried pipe to stay open in winter. Freezing usually means soil cover has eroded or been trampled, the line is shallow or exposed, or the tank sits too high and catches wind. The fix depends on which of those is happening.

What should I send before you come out?

Send the property town, photos of the waterer, the pond, and any wet spots along the line, what the waterer is doing now, roughly how many head use it, and how long the problem has been going on.

Do you work on the pond dam itself?

Repairs are focused on the watering system. If a problem involves the dam or spillway structure, we say so up front so the right resource can be involved before anything is dug.

Request a residential remodeling estimate.

Tell us where the property is and what needs to change. If the project is a fit, the next step is a walkthrough, measurements, and a written project plan.